The Original: Cost effective, waterwise irrigation
Microjet®, the cost-effective watering system that waters more efficiently using less water. Perfect for domestic gardens in South Africa. Save water, Save money.
WHY WATERWISE IRRIGATION:
With water becoming a scarce resource, we are all looking for waterwise irrigation methods. The Microjet® irrigation technology waters at a lower pressure and low volume, meaning less water is used.
SAVE WATER:
The water is concentrated over a small area for more efficient watering around the plant root zone. Watering closer to the ground and the plant also means less water is lost to evaporation.
CUSTOMISE:
With the Microjet®, you can also choose which cap to use, which then allows watering in a particular direction (360°, 180°, 90°), reducing the amount of run off and water wasted even further.
Selected products available at selected:
Microjet® Jets:
Microjet jets are made up of a selection of bases (affects water discharge) and caps (affects spray patterns) that are interchangeable. Select the base and cap combination that best suits the area that you are watering. Microjet® Caps snap on to the Microjet® Base and direct the water discharged by the orifice in the base, in a particular discharge pattern. The caps are colour coded for their spray patterns (see below), These caps are manufactured of a high quality, U.V. stabilised engineering plastic for maximum resistance to degradation by sunlight. They are easily snapped off and on for easy cleaning using the Microjet Spanner or Punch.
Spray patterns as shown below are indicated by the colour of the caps
RED
360°
BLUE
180°
GREEN
90°
BLACK
40°
STRIP
(2 X 20°)
Microjet® Bases:
Microjet® bases are made to the same fine tolerances and quality as the caps. They are colour coded to indicate the orifice size, the blue base indicating an orifice of 1.0mm and the green base indicating an orifice of 1.3mm. The size of the orifice determines the discharge rate of the base at any given pressure. The blue base is the most widely used base and with an orifice of 1.0mm diameter discharges 23 litres per hour at 0.5 bar and 53.7 litres per hour at 2.5 bar operating pressure. The green base, with it’s orifice of 1.3mm, discharges water at a rate of 35 litres per hour at 0.5 bar and 83 litres per hour at 2.5 bar operating pressure.
All bases and caps are 100% interchangeable. The cap simply clips on to the base to form a complete Microjet®. The Microjet® base is threaded (2BA thread) with a cutaway section for easy insertion into the pipe. It can be screwed directly into polyethylene pipe or into a Rigid Riser tube or a Microjet® Stake assembly.
MICROJET®
BLUE BASE/RED CAP 360° PN001
This pre-assembled Microjet® comes with a blue base. The bases are colour coded to indicate the orifice size. The blue base is the most widely used base and has an orifice of 1.0mm diameter discharging on average 40 litres per hour at a 1.5 bar pressure. A green base with an orifice size of 1.3mm is also available. The green base discharges 64 litres per hour at a 1.5 bar pressure.
The red cap on this pre-assembled Microjet® has a circular (360°) spray pattern. The caps are colour coded for their spray patterns. They are also available in blue (half circle -180°), green (quarter circle – 90°) and black (strip spray 2 x 20°)
All bases and caps are 100% interchangeable. The cap simply clips on to the base to form a complete Microjet®. The Microjet® base is threaded (2BA thread) with a cutaway section for easy insertion into the pipe. It can be screwed directly into polypipe or into a 4mm Rigid Riser tube or a Microjet® Stake assembly.
MICROJET®
BLUE BASE/BLUE CAP 180° PN002
This pre-assembled Microjet® comes with a blue base. The bases are colour coded to indicate the orifice size. The blue base is the most widely used base and has an orifice of 1.0mm diameter discharging on average 40 litres per hour at a 1.5 bar pressure. A green base with an orifice size of 1.3mm is also available. The green base discharges 64 litres per hour at a 1.5 bar pressure.
The blue cap on this pre-assembled Microjet® has a half circular (180°) spray pattern. The caps are colour coded for their spray patterns. They are also available in red (circular -360°), green (quarter circle – 90°) and black (strip spray 2 x 20°)
All bases and caps are 100% interchangeable. The cap simply clips on to the base to form a complete Microjet®. The Microjet® base is threaded (2BA thread) with a cutaway section for easy insertion into the pipe. It can be screwed directly into polypipe or into a 4mm Rigid Riser tube or a Microjet® Stake assembly.
MICROJET®
BLUE BASE/GREEN CAP 90° PN 003
This pre-assembled Microjet® comes with a blue base. The bases are colour coded to indicate the orifice size. The blue base is the most widely used base and has an orifice of 1.0mm diameter discharging on average 40 litres per hour at a 1.5 bar pressure. A green base with an orifice size of 1.3mm is also available. The green base discharges 64 litres per hour at a 1.5 bar pressure.
The green cap on this pre-assembled Microjet® has a quarter circular (90°) spray pattern. The caps are colour coded for their spray patterns. They are also available in red (full circle – 360°), blue (half circle -180°), and black (strip spray 2 x 20°)
All bases and caps are 100% interchangeable. The cap simply clips on to the base to form a complete Microjet®. The Microjet® base is threaded (2BA thread) with a cutaway section for easy insertion into the pipe. It can be screwed directly into polypipe or into a 4mm Rigid Riser tube or a Microjet® Stake assembly.
MICROJET®
BLUE BASE/BLACK CAP 40° PN 004
This pre-assembled Microjet® comes with a blue base. The bases are colour coded to indicate the orifice size. The blue base is the most widely used base and has an orifice of 1.0mm diameter discharging on average 40 litres per hour at a 1.5 bar pressure. A green base with an orifice size of 1.3mm is also available. The green base discharges 64 litres per hour at a 1.5 bar pressure.
The black cap on this pre-assembled Microjet® has a strip spray pattern (2 x 20°). The caps are colour coded for their spray patterns. They are also available in red (full circle – 360°), blue (half circle -180°), and green (quarter circle – 90°).
All bases and caps are 100% interchangeable. The cap simply clips on to the base to form a complete Microjet®. The Microjet® base is threaded (2BA thread) with a cutaway section for easy insertion into the pipe. It can be screwed directly into polypipe or into a 4mm Rigid Riser tube or a Microjet® Stake assembly.
MICROJET®
GREEN BASE/RED CAP 360° long range PN 005
This pre-assembled Microjet® comes with a green base. The green base has an orifice of 1.3mm and on average discharges 64 litres per hour at a 1.5 bar pressure.
The bases are colour coded to indicate the orifice size. The base is also available in blue, which is the most widely used and has an orifice of 1.0mm diameter, discharging on average 40 litres per hour at a 1.5 bar pressure.
The red cap on this pre-assembled Microjet® has a circular (360°) spray pattern. The caps are colour coded for their spray patterns. Caps are also available in blue (half circle -180°), green (quarter circle (90°) and black (strip spray 2 x 20°)
All bases and caps are 100% interchangeable. The cap simply clips on to the base to form a complete Microjet®. The Microjet® base is threaded (2BA thread) with a cutaway section for easy insertion into the pipe. It can be screwed directly into polypipe or into a 4mm Rigid Riser tube or a Microjet® Stake assembly.
MICROJET®
GREEN BASE/BLUE CAP 180° long range PN 006
This pre-assembled Microjet® comes with a green base. The green base has an orifice of 1.3mm and on average discharges 64 litres per hour at a 1.5 bar pressure.
The bases are colour coded to indicate the orifice size. The base is also available in blue, which is the most widely used and has an orifice of 1.0mm diameter, discharging on average 40 litres per hour at a 1.5 bar pressure.
The blue cap on this pre-assembled Microjet® has a half circular (180°) spray pattern. The caps are colour coded for their spray patterns. Caps are also available in red (circular -360°), green (quarter circle (90°) and black (strip spray 2 x 20°)
All bases and caps are 100% interchangeable. The cap simply clips on to the base to form a complete Microjet®. The Microjet® base is threaded (2BA thread) with a cutaway section for easy insertion into the pipe. It can be screwed directly into polypipe or into a 4mm Rigid Riser tube or a Microjet® Stake assembly.
MICROJET®
GREEN BASE/GREEN CAP 90° long range PN 007
This pre-assembled Microjet® comes with a green base. The green base has an orifice of 1.3mm and on average discharges 64 litres per hour at a 1.5 bar pressure.
The bases are colour coded to indicate the orifice size. The base is also available in blue, which is the most widely used and has an orifice of 1.0mm diameter, discharging on average 40 litres per hour at a 1.5 bar pressure.
The green cap on this pre-assembled Microjet® has a quarter circular (90°) spray pattern. The caps are colour coded for their spray patterns. They are also available in red (full circle – 360°), blue (half circle -180°), and black (strip spray 2 x 20°)
All bases and caps are 100% interchangeable. The cap simply clips on to the base to form a complete Microjet®. The Microjet® base is threaded (2BA thread) with a cutaway section for easy insertion into the pipe. It can be screwed directly into polypipe or into a 4mm Rigid Riser tube or a Microjet® Stake assembly.
MICROJET®
MICROMIST SPRAY
PN 013
The Micro Mist Spray is a Microjet® with a specially designed cap and base which produces a very fine mist, used for the irrigation of plants which require a very gentle precipitation such as very fine seedlings.
The Micromist spray is ideal for hothouses or any indoor area where humidity control is required. The Micromist discharges 13.3 litres per hour at an operating pressure of 0.5 bar to 28.0 litres per hour at an operating pressure of 2.5 bar.
MICROJET®
FRAMEJET 360° PN 020
The Microjet® Framejet is an open framed Microjet® with a standard Microjet® base, in this case a blue base. Any Microjet® base can be used depending on the required flow rate, which will affect the extent of the wetted area.
The Framejet is available in three different spray configurations: 360°, 180°, 90°, this one providing a 360°, circular spray pattern.
The Framejet is easy to clean, strong and reliable. It is made with a full two-sided frame instead of the “G” frame like many similar products. This ensures that the orifice and the deflector are perfectly aligned even after twisting during the assembly process to ensure a regular and even spray pattern.
The Framejet has a hook on the top of the frame to allow it the be suspended from the trellis wire should it be used on row crops.
The extent of the wetted area will vary depending on the size of the base and the operating pressure.
MICROJET®
FRAMEJET 180° PN 021
The Microjet® Framejet is an open framed Microjet® with a standard Microjet® base, in this case a blue base. Any Microjet® base can be used depending on the required flow rate, which will affect the extent of the wetted area.
The Framejet is available in three different spray configurations: 360°, 180°, 90°, this one providing a 180°, half circular spray pattern.
The Framejet is easy to clean, strong and reliable. It is made with a full two-sided frame instead of the “G” frame like many similar products. This ensures that the orifice and the deflector are perfectly aligned even after twisting during the assembly process to ensure a regular and even spray pattern.
The Framejet has a hook on the top of the frame to allow it the be suspended from the trellis wire should it be used on row crops.
The extent of the wetted area will vary depending on the size of the base and the operating pressure.
MICROJET®
FRAMEJET 90° PN 022
The Microjet® Framejet is an open framed Microjet® with a standard Microjet® base, in this case a blue base. Any Microjet® base can be used depending on the required flow rate, which will affect the extent of the wetted area.
The Framejet is available in three different spray configurations: 360°, 180°, 90°, this one providing a 90°, quarter circular spray pattern.
The Framejet is easy to clean, strong and reliable. It is made with a full two-sided frame instead of the “G” frame like many similar products. This ensures that the orifice and the deflector are perfectly aligned even after twisting during the assembly process to ensure a regular and even spray pattern.
The Framejet has a hook on the top of the frame to allow it the be suspended from the trellis wire should it be used on row crops.
The extent of the wetted area will vary depending on the size of the base and the operating pressure.
MICROSPIN
SPINNER Blue 360 PN 023
As its name implies the Microjet® Microspin is a highly accurate and efficient small sprinkler with a spinning rotor. Unlike many other spinners on the market today, the Microspin has a double-sided frame and not a single legged “G” shape, to give it extra strength and to ensure that the rotor runs straight. The rotor has a double throw and has aerodynamic design which makes it suitable in high wind conditions. Single pole rotors with an “arm” sticking out to the side tend to be badly effected by wind.
The rotor is made of molybdenum filled acetal which has self lubricating properties and the hook is made from PBT which is a very hard material.
Being part of the Microjet® family, the Microspin conforms to Microjet® specifications and standards and is available the following orifice sizes: Black (0.8mm), Orange (0.9mm), Blue (1.0mm), Green (1.3mm) and Red (1.5mm). Like the Microjet® bases the colour denotes the orifice and therefore the output. In the case of the Microspin, however the hook is colour coded for this purpose. In this case the Microspin has a blue base.
The Microspin is made of the following parts :
- Strong, Durable frame made from high quality engineering plastic.
- Highly efficient and accurate spinner. The spinner can be removed and replaced by twisting out the hook attachment
- Available in 2BA (threaded) or 4mm Barbed configuration.
- Detachable hook, which can be used to suspend the sprinkler from trellis wires.
- Supporting lugs for use when hanging Microspin from trellis wires.
MICROJET®
FRAMEJET 360° PN 0204
The Microjet® Framejet The Microjet® Framejet Downspray is part of the low pressure low volume Microjet® range of sprinklers. It is especially designed to irrigate small spaces such as pots or small beds in paved areas. The diameter of spray is much reduced by the shape of the deflector and this makes it ideal for irrigating plants where the wetting of leaves or foliage is not wanted. It can also be used for small trees or bushes where the spray needs to be contained close to the plant and can be replaced once the tree grows with a normal spray Microjet or Framejet. Should an adjustment to the amount of water be needed a Microjet choke can be
installed inline or the Varijet Downspray with a built in tap can be used instead.
Framejet Downspray is PERFECT FOR: Small Shrubs, small trees or pots.
Microjet® Accessories:
MICROJET®
Punch tool PN040
Microjet® Spanners and Punches are used to :
- Form the hole into which the Microjet® is to be screwed
- Screw the Microjet® into the hole
- Snap the Cap off for cleaning
All of the Microjet® Spanners and Punches have a spike or punch portion and a hexagonal socket which accurately fits the hexagon on the Microjet® base.
The Microjet® Punch is fitted with a stainless steel tubular punch which removes a small slug from the polyethylene pipe thus forming the correct size hole to receive the Microjet®. This slug is prevented from entering the pipeline by it’s retention within the handle of the punch.
A hexagon socket at the back of the handle is used to screw the Microjet® into the pipe.
The Microjet® Punch comes complete with a cap to cover the sharp punch tip when not in use.
MICROJET®
Spanner PN041
This is the original Microjet® spanner and consists of the t-bar section with a plastic spike and a hexagonal socket. It is the economy model which is used mainly in the home garden or areas where not too many Microjets® are to be installed
The Microjet® spanners and punches are used to :
- Form the hole into which the Microjet® is to be screwed
- Screw the Microjet® into the hole
- Snap the Cap off for cleaning
All of the Microjet® spanners and punches have a spike or punch portion and a hexagonal socket which accurately fits the hexagon on the Microjet® Base.
MICROJET®
Rigid Riser 450mm (with adaptor) PN044
Microjet® Rigid Risers are 450mm high and 4mm wide (inside diameter) high density polyethylene tubes. They are used to install Microjets® above the soil surface where the lateral line is installed below the surface or to extend the height of the emitter above undergrowth where the lateral is installed on the surface of the soil.
They are also used on a Microjet® Stake Assembly to extend the height of the Microjet® to spray over foliage
Microjet® Rigid Risers are extruded straight and accurately machine-cut to different lengths to ensure that the cut is exactly square to the tube. At no time during the manufacturing process are the tubes bent or coiled as the material of manufacture has an inherent memory which results in a pipe which is coiled or bent during manufacture returning to it’s original shape when relaxed. By extruding the risers straight, a perfectly straight end product is ensured with no bending once installed in the field. The accurate cut ensures that the adaptor and jet are fitted correctly and will not leak. All rigid risers are supplied complete with adaptors already fitted.
It is advisable to support the rigid risers with a Microjet® Stake to ensure that they stand upright .
MICROJET®
Flexible PVC Tubing
PN 060:
Microjet® flexible PVC tubing is made of high quality flexible pvc with UV inhibitors to ensure maximum resistance to degradation by the sun. The tubing is available in rolls of 100m or precut lengths which are attached and sold as part of the Microjet® stake assembly range. Precut lengths are supplied pre-assembled with the Microjet barbed connector.
MICROJET®
Mistake Corrector Plug (Barbed) PN046
This barbed mistake corrector plug (also known as Blank or Goof plug) is used to repair holes which have been made in the wrong position in polyethylene pipe or if Microjets®, Rigid Risers or Stake Assemblies need to be moved. The plug is simply pushed into the unwanted hole and seals, with the barb preventing it from falling out. It has a very neat finish as the plug, once inserted, lies flush with the pipe and is not easily visible
MICROJET®
5mm Tube Adaptor
PN048
Microjet® 5mm Tube Adaptors are used to connect 5mm flexible tubing to polyethylene lateral pipelines.
They can also be used to connect flexible tubing to Rigid Risers (usually to make movable stake assemblies) or to join pieces of tubing together.
This adaptor is threaded on one side and has a 5mm barb on the other side. The screwed end is either screwed into the polyethylene pipeline or rigid riser and the flexible tube is fitted to the 5mm barbed end.
MICROJET®
5mm Barbed Teepiece for flexible PVC Tubing PN049
The Microjet® 5mm Teepiece is to be used with the 5mm Microjet® PVC tube. They can be used to run two or more stake assemblies from one feedline. They can also be used as air lines for fish tanks and fuel lines for small engines.
MICROJET®
5mm Barbed Connector for flexible PVC tubing PN050
The Microjet® Barbed Adaptor is a tube adaptor that is used to connect 5mm flexible tubing to polyethylene lateral pipelines. They can also be used to connect flexible tubing to Rigid Risers (usually to make movable stake assemblies) or to join pieces of tubing together.
This Microjet® Barbed Adaptor is called the “Disc Adaptor” because it has a fairly large disc in the centre of the body. This disc makes it easier to grip the adaptor when inserting it into the tube. It is also easier to press into the polyethylene pipe once the hole has been made in the pipe with the Microjet® Punch or Spanner as it has more area to grip. This is the standard adaptor used on the majority of the Microjet® Stake Assemblies.
MICROJET®
Choke (Barbed)
PN053
Microjet® Chokes are used in conjunction with 5mm Flexible PVC Tube or with Rigid Risers to restrict the volume of water passing through the tube. They are ideal for areas, such as potplants, where the watering amount might need to be adjusted to fit a certain area. Microjet® Chokes also solve the problem of plants that require differing amount of water at different times of the year. With a Microjet® Choke installed that line or riser can simply be switched off when not needed.
It is important to note that these are Chokes and do not necessarily shut off the water supply completely
This choke has a 5mm barb on both ends and is designed for insertion in 5mm small bore tubing to control the discharge through the tube.
SNAP-ON®
PN105 for ½” Hose- or Polypipe
PN106 for ¾” Hose- or Polypipe
The Snap-on® / Emjay® Hose Connector is designed for use with either a hosepipe or polypipe. It is a more permanent connection and is ideal for use where the pressure in the pipe can build up. This happens when the hose nozzle at the other end of the hose is closed off and the hose pressure builds up to mains pressure. In this situation the standard Hose Connector could blow off and it is better to use this connector with a hose clamp.
It is available in ½” (15mm) and ¾” (20mm) fitting.
SNAP-ON®
PN117 Pipe Connector 15mm full flow
PN118 Pipe Connector 20mm full flow
The Snap-on® Full Flow® pipe connector has a Full Flow® compression end which allows a temporary connection of the Microjet® irrigation system (Polypipe) directly to the tap. This negates the use of hosepipes, clamps or complicated screwed connections to the tap. Connecting and disconnecting is as easy as “Snap on” or “Snap off”. This fitting will only work with Full Flow® compatible polypipe. Full Flow Fittings page. It comes in a 15mm or 20mm diameter. (the diameter indicates the polypipe that fits into it)
SNAP-ON®
Microjet® Shrubspray Adaptor PN064
Microjet® Shurbspray Adaptor screws onto the top of a ½” (15mm) Stand Pipe of Poly Riser. It can accommodate a Microjet pop-up nozzles or equivalent nozzles from all major pop-up manufacturers
Ideal for thick brush and shrubs
Microjet® Stakes:
MICROJET®
Slimstake 450mm
(Clip Head with Jet Adaptor) PN054
Microjet® Stake assemblies are factory assembled stake, tubing, riser and jet combinations – These are ready for immediate use without further work. You get Complete Stake Assemblies and Incomplete Stake Assemblies.
Complete Stake Assemblies have a jet pre-assembled on the stake whereas the Incomplete Stake Assemblies have no jet and the customer needs to select the appropriate jet and install it on the jet adaptor.
This 450mm high stake comes with a clip head and a jet adaptor but still requires a jet of your choice to be assembled on the top and PVC tubing to be installed onto the bottom of the jet adaptor, as well as a barbed connector/tube connector to connect the flexible PVC tubing to the polypipe.
MICROJET®
Slimstake Assembly 450mm
Incomplete - No Jet PN055
(comes with black pvc tube)
Microjet® Stake assemblies are factory assembled stake, tubing, riser and jet combinations – These are ready for immediate use without further work. You get Complete Stake Assemblies and Incomplete Stake Assemblies.
Complete Stake Assemblies have a jet pre-assembled on the stake whereas the Incomplete Stake Assemblies have no jet and the customer needs to select the appropriate jet and install it onto the jet adaptor.
This 450mm high stake comes with a clip head, jet adaptor and a 600mm length of PVC pipe with a polypipe connector. Only the appropriate Microjet® needs to be added (sold separately). The chosen Microjet® would be installed on top of the jet adaptor.
MICROJET®
Slimstake AssemblY 450mm Blue Base 360° Cap PN056 (comes with black pvc tube, the blue base and Full Circle Microjet)
Microjet® Stake assemblies are factory assembled stake, tubing, riser and jet combinations – These are ready for immediate use without further work. You get Complete Stake Assemblies and Incomplete Stake Assemblies.
Complete Stake Assemblies have a jet pre-assembled on the stake whereas the Incomplete Stake Assemblies have no jet and the customer needs to select the appropriate jet and install it onto the jet adaptor.
This 450mm high stake is a complete stake assembly and comes with a clip head, jet adaptor, 360° Microjet® with blue base and a 600mm length of PVC pipe, with a polypipe connector.
The Microjet® blue base is the most widely used base and has an orifice of 1.0mm diameter discharging on average 40 litres per hour at a 1.5 bar pressure. The red cap has a circular (360°) spray pattern.
MICROJET®
Slimstake Assembly 450mm
Blue Base 180° Cap PN057
(comes with black pvc tube and the blue base and 180° cap)
Microjet® Stake assemblies are factory assembled stake, tubing, riser and jet combinations – These are ready for immediate use without further work. You get Complete Stake Assemblies and Incomplete Stake Assemblies.
Complete Stake Assemblies have a jet pre-assembled on the stake whereas the Incomplete Stake Assemblies have no jet and the customer needs to select the appropriate jet and install it onto the jet adaptor.
This 450mm high stake is a complete stake assembly and comes with a clip head, jet adaptor, 180° Microjet® with blue base and a 600mm length of PVC pipe, with a polypipe connector.
The Microjet® blue base is the most widely used base and has an orifice of 1.0mm diameter discharging on average 40 litres per hour at a 1.5 bar pressure. The blue cap has a semi circular (180°) spray pattern.
MICROJET®
Slimstake Assembly 450mm Blue Base 90° Cap PN058 (comes with black pvc tube and a blue base and Quarter Circle Microjet)
Microjet® Stake assemblies are factory assembled stake, tubing, riser and jet combinations – These are ready for immediate use without further work. You get Complete Stake Assemblies and Incomplete Stake Assemblies.
Complete Stake Assemblies have a jet pre-assembled on the stake whereas the Incomplete Stake Assemblies have no jet and the customer needs to select the appropriate jet and install it onto the jet adaptor.
This 450mm high stake is a complete stake assembly and comes with a clip head, jet adaptor, 90° Microjet® with blue base and a 600mm length of PVC pipe, with a polypipe connector.
The Microjet® blue base is the most widely used base and has an orifice of 1.0mm diameter discharging on average 40 litres per hour at a 1.5 bar pressure. The green cap has a quarter circular (90°) spray pattern.
MICROJET®
Pot Stake PN 059
The Microjet® Potstake is a special configuration from our range of Stake Assemblies. As in all Stake Assemblies, the Microjet® Potstake comes from the factory pre-assembled, tested and ready to use with minimal work.
The Microjet® Potstake is designed for use in plant pots where the water spray can be accurately controlled and only spray in the pot, not over the sides, while still wetting as much as possible of the soil / foliage.
The adjustable Varijet Downspray will allow the user to finely adjust the spray to ensure that there should be very few dry spots in the pot as well no overwatering. This makes the Potstake a superior method of watering pot plants to using hosepipes, watering cans or drippers. The varijet downspray has a circlular (360°) spray pattern.
The biggest difference between the Microjet® Potstake and the other Stake Assemblies is that the Potstake does not come with tubing. This is because the applications where it will be used will require differing lengths of tubing and therefore it is not possible to have it pre-assembled with tubing.
The Microjet® Potstake consists of: A 150mm Microjet® Stake, A short piece of rigid riser (about 100mm), A tube adaptor (BG04) and Microjet® Varijet® Downspray.
Microjet® PVC tubing (black) and Tube Fittings (Adaptors, Tees) should be used to connect the Potstake to the water supply.(These items are purchased separately)
Installing your Microjet® system is easy and rewarding. Plan your installation here.